Over the past four years, I've processed roughly 140 purchase orders for electrical maintenance gear—everything from Omron PLC modules to multimeter cables to variable frequency drives (VFDs). In more than half of those orders, the cheapest option ended up costing us more than the pricier alternative.
The worst was a batch of multimeter cables we bought for $85. Two of the four cables failed within a week—bad readings. One of our maintenance techs used a faulty cable to check a fuse with a multimeter, misread the voltage, swapped a good fuse, and missed the real fault. That brought a packaging line down for four hours. The downtime cost us about $1,800. That's 20 times what we saved on the cables.
Since then, I don't look at unit price anymore. I look at total cost—including the cost of the thing failing.
I'm the office administrator for a 75-person manufacturing company. I manage all maintenance supplies ordering—roughly $180,000 annually across 8 vendors. I report to both operations and finance. I'm not an automation engineer. I don't program the Omron PLCs or commission VFDs. But I see the invoices, the downtime reports, and the frantic emails when a "value" part fails at 2 a.m.
In our 2023 vendor consolidation project, I had to streamline orders for three facilities. That's when I started tracking more than just the line item price. I wish I had tracked it from the start—I don't have hard data on how many of our early failures were price-driven, but looking back at maintenance logs, my sense is it was a meaningful chunk.
Checking a fuse with a multimeter is one of the most basic maintenance tasks. You set the meter to continuity or resistance mode, touch the probes to both ends of the fuse, and see if you get a near-zero reading. No reading—or infinite resistance—means the fuse is blown.
The catch? The reading is only as good as your multimeter cables. The cheap set we bought had high contact resistance. Our tech got a slightly odd reading and thought the fuse was going bad. He replaced it. The machine still didn't start. He spent another 40 minutes chasing the wrong problem before a senior tech grabbed a different cable and found the actual fault.
Now we buy cables from an authorized test-equipment distributor. Four cables run about $120 (versus $85 for the cheap set). That's a $35 difference. Worth every penny—because one misdiagnosis cost us $1,800 in lost production.
We run a mix of Omron PLCs—the NJ series for our more complex multi-axis machines, and the CJ2M for simpler packaging lines.
A while back, we tried to save money by using a CJ2M substitute for a failed NJ-series module on a machine that only did basic logic. Seemed like it should work. It didn't. The NJ series and CJ2M use different communication protocols and programming environments. Our engineer burned two weeks trying to get the CJ2M to talk to the existing NX I/O modules. The project went over budget, and we missed a maintenance window.
That mistake turned into a standard question in our purchase process: "Is this part compatible with our existing Omron PLC architecture?" If the answer isn't a clear yes, we don't buy the cheaper version. A $400 module isn't a deal if it costs two weeks of engineering time.
We don't buy variable frequency drives often—maybe two or three a year. But we had a VFD fail on a critical pump, and we needed a replacement fast.
The vendor had two options: a name-brand unit at $1,400 and a cheaper alternative at $800. Specs looked identical on paper. We went with the cheaper one.
The VFD itself ran fine. But: it needed an extra line reactor to meet our harmonic requirements (another $250). The programming software wasn't as intuitive—our electrician spent an extra three hours on setup. And it wouldn't communicate with our Omron PLC via Modbus without a separate gateway module ($150). So the $600 savings turned into about $1,200 in extras. Plus a full day of extra labor. I should mention that this was in 2023, and we've since standardized on a few VFD brands that our team knows.
I'm not saying buy the most expensive option every time. That's just as lazy as always buying the cheapest. For basic stuff—DIN rail, standard fuses, wire ferrules, cable ties—the cheapest option is fine. I buy those in bulk and don't overthink it.
My experience is based on about 75 people and roughly 20 different machines. If you're running a much larger plant, your buying volume might give you more leverage. And if you're a smaller shop with three machines, your risk profile is different.
But if a part touches diagnostics or machine control—multimeter cables, PLC modules, VFDs—the lowest unit price is usually a trap. The cost of one misdiagnosis, one compatibility headache, or one hour of unplanned downtime will eat every dollar you saved. I learned that the expensive way, so you don't have to.